There are two common elevator door pocket styles. One is the vertical edge and the horizontal edge with an angle of 90 degrees, so it looks like the line is very straight and the scene splicing is very convenient, which is also a common style; The other is a 45 degree angle, so the door frame forms a whole without inflection point, so the whole door pocket looks like a whole. The two styles have their own advantages, convenient 90 degree splicing and low cost. 45 degrees looks good, but it is difficult. The coincidence degree is not high. It requires free cutting, and the cost is higher than 90 degrees. It is usually recommended to customers that 90 degree splicing is more economical.

電梯廳不銹鋼電梯門套工藝節點優化，如何優化結構，避免材料浪費。一般預防措施如下：

Elevator hall stainless steel elevator door pocket process node optimization, how to optimize the structure and avoid material waste. General precautions are as follows:

1、材料推薦厚度為1.5（實際厚度應不小于1.38）

1. The recommended thickness of the material is 1.5 (the actual thickness shall not be less than 1.38)

2、門頭板的寬度小于內板的寬度，這樣門才會美觀。

2. The width of the door head plate is less than that of the inner plate, so that the door will be beautiful.

3、注意生產基地必需小于5mm的門裝訂尺寸，以保證有足夠的安裝和涂膠空間。

3. Note that the door binding size of the production base must be less than 5mm to ensure sufficient installation and gluing space.

4、一般不建議用膠水封住門頭板與外墻覆層交界處的內角。美觀大方，可以檢查門套的安裝質量。

4. It is generally not recommended to seal the inner corner of the junction between the door headboard and the outer wall cladding with glue. Beautiful and generous, you can check the installation quality of the door pocket.

不銹鋼門套與石材碰撞，如何避免石材封閉邊緣的“閃縫”缺陷？

How to avoid the "flash joint" defect of the closed edge of the stone when the stainless steel door pocket collides with the stone?

1、常規封口的缺點：石材不能保證下一條直線，所以這種封口可能會出現不銹鋼插入或石材閃縫過大等情況。石材邊緣在安裝過程中可能會損壞。

1. Disadvantages of conventional sealing: the stone can not guarantee the next straight line, so this kind of sealing may have stainless steel insertion or too large stone flash joint. Stone edges may be damaged during installation.

2、加深封口：不銹鋼封口石可以防止石材封邊的缺陷，使其干凈美觀。

2. Deepen sealing: stainless steel sealing stone can prevent the defects of stone edge sealing and make it clean and beautiful.

門套一體成型，錯位、彈跳等質量問題是非標底座造成的。建議將擋板與蓋板分開，避免因底座問題造成的安裝缺陷。

The door pocket is integrally formed, and the quality problems such as dislocation and bounce are caused by non-standard base. It is recommended to separate the baffle plate from the cover plate to avoid installation defects caused by base problems.

各位顧客，以上關于工地電梯門套http://www.hmqczz.com知識分享，希望能幫助新手，在使用中有任何疑問，請隨時聯系相關人員，我們將為您提供周到的技術支持服務。

Dear customers, the above information about the elevator door pocket on the construction site http://www.hmqczz.com Knowledge sharing, hope to help novices. If you have any questions in use, please feel free to contact relevant personnel, and we will provide you with thoughtful technical support services.